Menu
Industrial Automation
D6FZ-FGT Series
Air Flow Sensor
The best Product to Measure Compressed Air at Machine. Measurement of Leakage and Usage.
Related Contents
Application Solutions
- Features
- Lineup
- Specifications
- Dimensions
- Catalog / Manual / CAD / Software
last update: March 1, 2023
Ratings
Air Flow Sensor
| Model | D6FZ-FGT200 | D6FZ-FGT500 | ||
|---|---|---|---|---|
| Applicable fluid | Air or nitrogen (N2) *1 | |||
| Working pressure | 0.75MPa (withstand pressure 1.5MPa) | |||
| Measurement range*2 | 0 to 200L/min | 0 to 500L/min | ||
| Measurement accuracy
range*2 |
2 to 200L/min | 5 to 500L/min | ||
| Display Resolution*2 | 1L/min | |||
| Accuracy*2 | ±2.0%F.S. at 50L/min or more | |||
| ±0.5%F.S. at less than 50L/min | ||||
| Temperature characteristic | ±3%F.S. | |||
| Repeat accuracy | ±1%F.S. | |||
| Operating temperature | Operation: -10 to 60°C / Storage: -20 to 70°C (no condensation or icing) | |||
| Operating humidity | Operation: 25 to 90%RH / Storage: 0 to 90%RH (no condensation or icing) | |||
| Shock resistance | 150 m/s2 in 6 directions (+/-X, +/-Y, and +/-Z directions), 3 times each | |||
| Pressure loss | 2kPa max. | 4kPa max. | ||
| Power supply voltage | 12 to 24 VDC ±10% ripple (p-p) 10% max. | |||
| Current consumption | 120mA max. | |||
| Functions | Momentary flow / Integrated flow / Reversing display / Zero point Adjustment /
Peak and Bottom Hold / Key Lock / Eco Mode / Scaling (Analog Output) / Judgement Hysteresis / Teaching |
|||
| Display | 11-segment digital display (Red), RUN / FUN / THR (Yellow),
Out1 / Out2 (Yellow), Key Lock (Yellow), Flow unit (Green), Flow unit in reversed display (Yellow) |
|||
| Output | Output
interface |
Analog | Current output 4 to 20mA (1 contact), maximum load resistance 300Ω max. | |
| ON/OFF | Open collector output (2 outputs) 26.4 VDC 50mA max.
ON residual voltage 2V max. (Outputs can be selected from judgement output, pulse output and unit error output) |
|||
| RS-485 | 2-wire half duplex communication, start-stop synch method
Baud rate: 9.6k/19.2k/38.4k/115.2kbps, data bit length: 7/8bit, stop bit length: 1/2bit, parity: none/even/odd, termination resister (120Ω): ON/OFF, communications protocol: compatible with CompoWay/F |
|||
| Output values | Momentary flow, Integrated flow, Judgement output *3, Unit error output | |||
| Degree of protection | IP65 | |||
| Installation Direction and
Straight Pipe Section |
A straight pipe section must be provided during installation and piping if the Sensor is
installed horizontally and the display is on the top. *4 |
|||
| Connection bore diameter | Rc1/4 (8A) | Rc1/2 (15A) | ||
| Material | Main unit: PBT / Flow channel: Zinc | |||
| Dimensions | 30(W) × 77(D) × 63.7(H) mm | |||
| Weight (in package) | Approx. 400 g (500 g) | |||
| Accessories | Instruction Sheet | |||
*1. Clean Dry Gas (must not contain large particle e.g. duct, oil and mist)
*2. Converted value assuming the accumulated flow quantity following conditions
std (factory default) : 20°C at 1 atmospheric pressure 101.3kPa, nor : 0°C at 1 atmospheric pressure 101.3kPa
*3. To prevent chattering, a judgement output is made when the judgement continues for one minute or longer.
*4. The accuracy will depend on the length of the straight pipe section. Refer to Flow rate accuracy characteristics for a
length of straight pipe on Catalog for details.
*2. Converted value assuming the accumulated flow quantity following conditions
std (factory default) : 20°C at 1 atmospheric pressure 101.3kPa, nor : 0°C at 1 atmospheric pressure 101.3kPa
*3. To prevent chattering, a judgement output is made when the judgement continues for one minute or longer.
*4. The accuracy will depend on the length of the straight pipe section. Refer to Flow rate accuracy characteristics for a
length of straight pipe on Catalog for details.
Air Flow Station
| Model | D6FZ-FGX21 |
|---|---|
| Connectable sensor | D6FZ-FGT200 / D6FZ-FGT500 / D6FZ-FGS1000 |
| Maximum number of
mounted Sensors |
8 units*1 |
| Display | 7-seg. 5-digit 2-step LCD display, auxiliary information indicator displays |
| Recording interval | 1 s, 2 s, 5 s, 10 s, 20 s, 30 s, 1 min. |
| Displayed data | Momentary flow rate, integrated flow rate, pressure, temperature, charge/CO2
conversion value |
| Recorded data | Momentary flow rate, integrated flow rate, volume flow rate, pressure, temperature |
| Operation function | Conversion of integrated flow rate to charge/CO2 |
| Recording mode | Continue mode*2, Ring mode*3 |
| External output | Alarm output (Photocoupler output) *4 |
| Communication interface | Ethernet (10BASE-T, 100BASE-TX) |
| Internal storage device | Internal memory: Approx. 4200 data items when 1 unit is connected,
approx. 650 data items when 8 units are connected |
| External storage device | SD card (measured value saving/set value saving and reading), Recommended SD card:
HMC-SD291 (2 GB) *9 and HMC-SD491 (4 GB) (manufactured by OMRON) *5 |
| Power supply voltage | DC input: 24 VDC±10% ripple (p-p) 10% max. |
| Current consumption | 80 mA max. |
| Operating temperature | Without Ethernet: -10°C to 40°C (no condensation or icing),
with Ethernet: 0°C to 40°C (no condensation or icing) |
| Operating humidity | 35 to 85%RH (no condensation or icing) |
| Storage humidity/
temperature |
-15°C to 60°C, 20% to 85%RH (no condensation or icing) |
| Insulation resistance | 20 MΩ (500 VDC) |
| Withstand voltage | 1000 VAC, 50/60 Hz, 1 min. |
| Vibration resistance | 10 to 150 Hz, 0.7 mm double amplitude,
acceleration: 50 m/s2 for each in X, Y and Z directions for 80 min |
| Shock resistance | 150 m/s2 in 6 directions (+/-X, +/-Y, and +/-Z directions), 3 times each*6 |
| Material | ABS |
| Degree of protection | IP30 |
| Mounting | Magnet mounting, screw mounting, hook |
| Dimensions | 117.2(W) × 24.6(D) × 56.8(H) mm (Except protruding part) |
| Weight (in package) | Approx. 150 g (Approx. 500 g) |
| Accessories | Instruction Sheet, Startup Guide, T-branch connection cable*7, Alarm Output Connector*8 |
*1. Up to 8 units can be connected when the recording cycle is 2 seconds or longer; up to 4 units when the recording cycle is
1 second.
*2. Automatically writes the data to the SD memory card when the internal memory reaches its capacity and continues
recording until the SD card memory capacity reaches its limit.
The unit stops operation if there is no SD memory card inserted when the internal memory reaches its capacity, or when
it is write protected. (Recording can be resumed after inserting an SD memory card and outputting the data to it at a
press of button.)
The factory default is continue mode. Use the PC software to change the recording mode.
*3. Continues the recording of the latest measured values until the internal memory reaches its capacity. (If the internal
memory capacity exceeds the capacity, data is overwritten from the oldest one in the memory.)
*4. Output when the range of upper/lower limit of the air flow that has been set in threshold setting mode is exceeded.
*5. When using a third party SD card, it is recommended to use a reliable and durable industrial SD card (SD standard or
SDHC standard (not compliant with SDXC standard), Class 4 or higher, flash memory type SLC or MLC type).
You must confirm the operation of the SD card yourself.
*6. When using a mounting magnet, be sure to install it in a location where shock is not applied.
*7. A T-branch connector to connect to D6FZ-FC02.
*8. OMRON's XW4B-02B1-H1 connector
*9. Orders for HMC-SD291 will be accepted until the end of March 2022.
1 second.
*2. Automatically writes the data to the SD memory card when the internal memory reaches its capacity and continues
recording until the SD card memory capacity reaches its limit.
The unit stops operation if there is no SD memory card inserted when the internal memory reaches its capacity, or when
it is write protected. (Recording can be resumed after inserting an SD memory card and outputting the data to it at a
press of button.)
The factory default is continue mode. Use the PC software to change the recording mode.
*3. Continues the recording of the latest measured values until the internal memory reaches its capacity. (If the internal
memory capacity exceeds the capacity, data is overwritten from the oldest one in the memory.)
*4. Output when the range of upper/lower limit of the air flow that has been set in threshold setting mode is exceeded.
*5. When using a third party SD card, it is recommended to use a reliable and durable industrial SD card (SD standard or
SDHC standard (not compliant with SDXC standard), Class 4 or higher, flash memory type SLC or MLC type).
You must confirm the operation of the SD card yourself.
*6. When using a mounting magnet, be sure to install it in a location where shock is not applied.
*7. A T-branch connector to connect to D6FZ-FC02.
*8. OMRON's XW4B-02B1-H1 connector
*9. Orders for HMC-SD291 will be accepted until the end of March 2022.
last update: March 1, 2023
Top of page
Products
Menu
About Us
Menu
Solutions
Menu
Privacy
Menu
Services
Menu
Resources
Menu
© Copyright OMRON Corporation 2000-2020. All Rights Reserved.