Page top

Industrial Automation

Contact

Industrial Automation

E3Z-[]-UL

Compact Photoelectric Sensor with Built-in Amplifier

E3Z-[]-UL

The lineup has been expanded to standard photoelectric sensor E3Z series with UL certified products

Related Contents

last update: October 1, 2024

Standard Model

Sensing method Through-beam
Model NPN
output		 Pre-wired E3Z-T61-UL E3Z-T62-UL E3Z-T61A-UL
M8 Connector E3Z-T66-UL E3Z-T67-UL E3Z-T66A-UL
PNP
output		 Pre-wired E3Z-T81-UL E3Z-T82-UL E3Z-T81A-UL
M8 Connector E3Z-T86-UL E3Z-T87-UL E3Z-T86A-UL
Sensing distance 15 m 30 m 10 m
Spot diameter (reference value) ---
Standard sensing object Opaque: 12-mm dia. min.
Minimum detectable object (reference
value)		 ---
Differential travel (representative
example)		 ---
Directional angle Both emitter and receiver: 3 to 15°
Light source (wavelength) Infrared LED (870 nm) Red LED (660 nm)
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max. Class 2
Current consumption 35 mA max. (Emitter: 15 mA max., Receiver: 20 mA max.)
Control output Load power supply voltage: 26.4 VDC max., Load current: 100 mA max.
(Residual voltage: Load current of less than 10 mA: 1 V max. Load current of
10 to 100 mA: 2 V max.)
Open collector output (NPN/PNP depending on model)
Light-ON/Dark-ON selectable
Indicator Operation indicator (orange)
Stability indicator (green)
Through-beam Emitter has power indicator (orange) only.
Protection circuits Reversed power supply polarity protection, Output short-circuit protection,
and Reversed output polarity protection
Response time Operate or reset:
1 ms max.		 Operate or reset:
2 ms max.		 Operate or reset:
1 ms max.
Sensitivity adjustment One-turn adjuster
Ambient illumination (Receiver side) Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55°C, Some connector models: -40°C to 55°C *2 (with no
icing or condensation)
Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y,
and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Weight
(packedstate)		 Pre-wired cable (2 m) Approx. 120 g
M8 Connector Approx. 30 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Modified polyarylate

Sensing method Retro-reflective
with
MSR function		 Diffuse-reflective
(Narrow-
beam Models)
Model NPN
output		 Pre-wired E3Z-R61-UL E3Z-D61-UL E3Z-D62-UL E3Z-L61-UL
M8 Connector E3Z-R66-UL E3Z-D66-UL E3Z-D67-UL E3Z-L66-UL
PNP
output		 Pre-wired E3Z-R81-UL E3Z-D81-UL E3Z-D82-UL E3Z-L81-UL
M8 Connector E3Z-R86-UL E3Z-D86-UL E3Z-D87-UL E3Z-L86-UL
Sensing distance 4 m (100 mm) *1
(when using
E39-R1S)
3 m (100 mm) *1
(when using
E39-R1)		 100 mm
(white paper:
100 × 100 mm)		 1 m
(white paper:
300 × 300 mm)		 90 + 30 mm
(white paper,
100 x 100 mm)
Spot diameter (reference value) --- (2.5 dia. and
sensing distance
of 90 mm)
Standard sensing object Opaque: 75-mm
dia. min.		 ---
Minimum detectable object (reference
value)		 --- 0.1 mm (copper
wire)
Differential travel (representative
example)		 --- 20% max. of setting distance Refer to Engi-
neering data
on Data Sheet.
Directional angle 2 to 10° ---
Light source (wavelength) Red LED
(660 nm)		 Infrared LED (870 nm) Red LED
(650 nm)
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max. Class 2
Current consumption 30 mA max.
Control output Load power supply voltage: 26.4 VDC max., Load current: 100 mA max.
(Residual voltage: Load current of less than 10 mA: 1 V max. Load current of
10 to 100 mA: 2 V max.)
Open collector output (NPN/PNP depending on model)
Light-ON/Dark-ON selectable
Indicator Operation indicator (orange)
Stability indicator (green)
Through-beam Emitter has power indicator (orange) only.
Protection circuits Reversed power supply polarity protection, Output short-circuit protection,
Mutual interference prevention, and Reversed output polarity protection
Response time Operate or reset: 1 ms max.
Sensitivity adjustment One-turn adjuster
Ambient illumination (Receiver side) Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55°C, Some connector models: -40°C to 55°C *2 (with no
icing or condensation)
Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y,
and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Weight
(packedstate)		 Pre-wired cable (2 m) Approx. 65 g
M8 Connector Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Methacrylic resin Modified polyarylate

Note: 1. Altitude: Up to 2000 m, Pollution degree: 3, Enclosure type: Type1.
*1. Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.
*2. The ambient temperature range during operation for connector models depends on the model.
      For the E3Z-T66/T86/R66/R86, the range is -40°C to 55°C. E3Z-D66/D86/D67/D87, the range is -30°C to 55°C. Other connector models, the range is -25°C to -55°C.
      The sensing distance for Retro-reflective Models (E3Z-R66/R86) between -40°C to -25°C, however, will be as follows (not the values in the table).
      E39-R1S: 3 m (100 mm) *1, With E39-R1: 2 m (100 mm) *1.
      Also, use the XS3F-M42[]-4[][]-L Sensor I/O Connector (PUR cable) for applications between -25°C to -40°C.

Sensing method Distance-settable
Pre-wired M8 Connector Pre-wired M8 Connector
Model NPN output E3Z-LS61-UL E3Z-LS66-UL E3Z-LS63-UL E3Z-LS68-UL
PNP output E3Z-LS81-UL E3Z-LS86-UL E3Z-LS83-UL E3Z-LS88-UL
Sensing
distance		 BGS White or black paper (100 × 100 mm):
20 mm to set distance		 2 mm to set distance (80 mm max.)
FGS White paper (100 × 100 mm):
Set distance to 200 mm min.
Black paper (100 × 100 mm):
Set distance to 160 mm min.		 -----
Setting range White paper (100 × 100 mm): 40 to 200
mm
Black paper (100 × 100 mm): 40 to 160
mm		 White paper (25 × 25 mm): 20 to 80 mm
Differential travel 10% of set distance max. (Refer to
Differential Travel vs. Sensing Distance
on Data Sheet.)		 2% of set distance max.
Reflectivity characteristic
(black/white error)		 10% of set distance max. 5% of set distance max.
Light source (wavelength) Red LED (670 nm) Red LED (650 nm)
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max. Class 2
Current consumption 30 mA max.
Control output Load power supply voltage: 26.4 VDC max., Load current: 100 mA max. (residual
voltage 1 V max.), Open collector output (NPN or PNP depending on model)
Light-ON/Dark-ON switch selectable
BGS/FGS selection BGS: Open or connected to GND
FGS: Connected to Vcc		 BGS: Open or connected to GND
Protection circuits Reversed power supply polarity protection, Output short-circuit protection, Mutual
interference prevention
Response time Operate or reset: 1 ms max.
Distance setting 5-turn endless adjuster
Ambient illumination (Receiver side) Incandescent lamp: 3,000 lx max.; Sunlight: 10,000 lx max.
Ambient temperature
range		 Operating: -25 to 55°C, Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Indicators Operation indicator (orange), Stability indicator (green)
Weight (packed state) Pre-wired cable
(2 m): Approx. 65 g		 Approx. 20 g Pre-wired cable
(2 m): Approx. 65 g		 Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Modified polyarylate resin
Accessories Instruction manual (Mounting Brackets must be ordered separately.)

Note: 1. Altitude: Up to 2000 m, Pollution degree: 3, Enclosure type: Type1.

Sensing method Transparent glass Limited-reflective (for transparent object detection)
Pre-wired M8 Connector
Model NPN output E3Z-L63-UL E3Z-L68-UL
PNP output E3Z-L83-UL E3Z-L88-UL
Sensing distance 30±20 mm (transparent glasses 100 × 100 mm)
Spot diameter (reference value) 2-mm dia. min. (at sensing distance of 30 mm)
Minimum detectable object (reference
value)		 0.1 mm dia. (copper wire)
Light source (wavelength) Red LED (660 nm)
Current consumption 30 mA max.
Protection circuits Power supply reverse polarity protection, Output short-circuit protection,
Mutual interference prevention, Reverse output polarity protection
Response time Operate or reset: 1 ms max.
Sensitivity adjustment One-turn adjuster
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Weight
(packed state)		 Pre-wired cable (2 m) Approx. 65 g
M8 Connector Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Modified polyarylate

Sensing method Retro-reflective for clear, plastic bottles (without MSR function)
Pre-wired M8 Connector Pre-wired M8 Connector
Model NPN output E3Z-B61-UL E3Z-B66-UL E3Z-B62-UL E3Z-B67-UL
PNP output E3Z-B81-UL E3Z-B86-UL E3Z-B82-UL E3Z-B87-UL
Sensing distance 500 mm (80 mm) *1
(using E39-R1S)		 2 m (500 mm) *1 *2
(using E39-R1S)
Standard sensing object Opaque materials, 75mm dia. min.
(Standard detectable object:glass Cylinder 15mm dia. thickness 1.1mm
length 50mm, and the transmission factor 92% or less in wave length
660nm)
Light source (wavelength) Red LED (660 nm)
Current consumption 30 mA max.
Protection circuits Reversed power supply polarity protection, Output short-circuit protection,
Mutual interference prevention, and Reversed output polarity protection
Response time Operate or reset: 1 ms max.
Sensitivity adjustment One-turn adjuster
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Weight
(packed state)		 Pre-wired cable (2 m) Approx. 65 g
M8 Connector Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Modified polyarylate

*1. Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.
*2. Plastic bottles must pass with the minimum clearance of 500 mm.

Common (Transparent glass Limited-reflective / Retro-reflective for clear, plastic bottles)

Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max. Class 2
Control output Load power supply voltage: 26.4 VDC max., Load current: 100 mA max.
(Residual voltage: Load current of less than 10 mA: 1 V max. Load current
of 10 to 100 mA: 2 V max.)
Open collector output (NPN/PNP depending on model)
Light-ON/Dark-ON selectable
Ambient illumination (Receiver side) Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55°C (with no icing or condensation)
Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y,
and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Indicator Operation indicator (orange)
Stability indicator (green)
Through-beam Emitter has power indicator (orange) only.
Accessories Instruction manual (Neither Reflectors nor Mounting Brackets are provided
with any of the above models.)

Note: 1. Altitude: Up to 2000 m, Pollution degree: 3, Enclosure type: Type1.

Laser Model

Sensing method Through-beam Retro-reflective
with
MSR function		 Distance-settable (BGS models)
Response Standard response High-speed response
Model NPN
output		 Pre-wired E3Z-LT61-UL E3Z-LR61-UL E3Z-LL61-UL E3Z-LL63-UL
M8 Connector E3Z-LT66-UL E3Z-LR66-UL E3Z-LL66-UL E3Z-LL68-UL
PNP
output		 Pre-wired E3Z-LT81-UL E3Z-LR81-UL E3Z-LL81-UL E3Z-LL83-UL
M8 Connector E3Z-LT86-UL E3Z-LR86-UL E3Z-LL86-UL E3Z-LL88-UL
Sensing distance 60 m 0.2 to 7 m
(when using E39-
R12)		 White paper (100
× 100 mm):
20 to 300 mm
Black paper (100
× 100 mm):
20 to 160 mm		 White paper (100
× 100 mm):
25 to 300 mm
Black paper (100
× 100 mm):
25 to 100 mm
Set distance range --- White paper (100
× 100 mm):
40 to 300 mm
Black paper (100
× 100 mm):
40 to 160 mm		 White paper (100
× 100 mm):
40 to 300 mm
Black paper (100
× 100 mm):
40 to 100 mm
Spot diameter (reference value) 5-mm dia. at 3 m 0.5-mm dia. at 300 mm
Standard sensing object Opaque: 12-mm
dia. min.		 Opaque: 75-mm
dia. min.		 ---
Minimum detectable object
(reference value)		 6-mm-dia. opaque object at 3 m 0.2-mm-dia. stainless-steel pin gauge
at 300 mm
Differential travel --- 5% max. of set distance
Black/white error --- 5% at 160 mm 5% at 100 mm
Directional angle Receiver: 3 to 15° ---
Light source (wavelength) Red LD (655 nm), JIS CLass 1, IEC Class 1, FDA Class 1
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max. Class 2
Current consumption 35 mA (Emitter 15
mA, Receiver 20
mA)		 30 mA max.
Control output Load power supply voltage: 26.4 VDC max., Load current: 100 mA max., Open
collector output
Residual output voltage Load current of less than 10 mA: 1 V max.
Load current of 10 to 100 mA: 2 V max.
Output mode switching Switch to change between light-ON and dark-ON
Protection circuits Reversed power
supply polarity
protection, Output
short-circuit
protection, and
Reversed output
polarity protection		 Reversed power supply polarity protection, Output short-
circuit protection, Mutual interfer- ence prevention, and
Reversed output polarity protection
Response time Operate or reset: 1 ms max. Operate or reset:
0.5 ms max.
Sensitivity adjustment One-turn adjuster Five-turn endless adjuster
Ambient illumination (Receiver
side)		 Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature range Operating: -10 to 55°C, Storage: -25 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no icing or condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IP67 (IEC 60529)
Connection method Pre-wired (standard cable length: 2 m) /
M12 Pre-wired Smartclick Connector (standard cable length: 0.3 m) /
M8 (4-pin) Connector
Indicator Operation indicator (orange)
Stability indicator (green)
Emitter for Through-bream Models has power indicator (orange) only.
Weight
(packed
state)		 Pre-wired cable (2 m) Approx. 120 g Approx. 65 g
M12 Pre-wired
Smartclick Connector
(0.3 m)		 Approx. 60 g Approx. 30 g
M8 Connector Approx. 30 g Approx. 20 g
Material Case PBT (polybutylene terephthalate)
Display Polycarbonate (PC)
Lens Modified
polyarylate resin		 Methacrylic resin Modified polyarylate resin
Accessories Instruction manual (Neither Reflectors nor Mounting Brackets are provided with
any of the above models.)

Note: 1. Altitude: Up to 2000 m, Pollution degree: 3, Enclosure type: Type1.

IO-Link Model

Sensing method Through-beam Retro-reflective
with
MSR function		 Diffuse-reflective Narrow-beam
Models
Model PNP
output		 Pre-wired E3Z-T81-IL[]-UL E3Z-R81-IL[]-UL E3Z-D82-IL[]-UL E3Z-L81-IL[]-UL
M8 Connector E3Z-T86-IL[]-UL E3Z-R86-IL[]-UL E3Z-D87-IL[]-UL E3Z-L86-IL[]-UL
Sensing distance 15 m 4 m (100 mm) *1
(when using E39-
R1S)
3 m (100 mm) *1
(when using E39-
R1)		 1 m
(white paper: 300
× 300 mm)		 90 + 30 mm
(white paper: 100
× 100 mm)
Spot diameter (reference value) --- 2.5 dia. and
sensing distance
of 90 mm
Standard sensing object Opaque: 12-mm
dia. min.		 Opaque: 75-mm
dia. min.		 ---
Minimum detectable object
(reference value)		 --- 0.1 mm (copper
wire)
Differential travel
(representative example)		 --- --- 20% max. of
setting distance		 Refer to Engi-
neering data on
Data Sheet.
Directional angle Both emitter and
receiver: 3 to 15°		 2 to 10° ---
Light source (wavelength) Infrared LED
(870 nm)		 Red LED (660 nm) Infrared LED
(870 nm)		 Red LED (650 nm)
Power supply voltage 10 to 30 VDC including ripple (p-p) Class 2
Current consumption 50 mA max.
(Emitter: 25 mA
max., Receiver: 25
mA max.)		 30 mA max.
Control output Load power supply voltage: 30 VDC max., Load current: 100 mA max.
Residual voltage:
Load current of less than 10 mA: 1 V max.
Load current of 10 to 100 mA: 2 V max.
PNP open collector output
Light-ON/Dark-ON selectable
Indicators In the Standard I/O mode (SIO mode): Operation indicator (orange, lit) and stability
indicator (green, lit)
In the IO-Link Mode: Operation indicator (orange, lit) and communication indicator
(green, blinking at 1 s intervals)
Protection circuits Reversed power
supply polarity
protection, output
short-circuit
protection, and
reversed output
polarity protection		 Reversed power supply polarity protection, output short-
circuit protection, reversed output polarity protection, and
mutual interference prevention
Response time Operate or reset: 1 ms max.
Sensitivity adjustment Sensitivity adjuster / IO-Link communications
Ambient illumination (Receiver
side)		 Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55°C (with no icing or condensation)
Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67
Connection method Pre-wired (standard cable length: 2 m) / M8 (4-pin) Connector
Weight
(packed
state)		 Pre-wired cable (2 m) Approx. 120 g Approx. 65 g
M8 Connector Approx. 30 g Approx. 20 g
Material Case Polybutylene terephthalate (PBT)
Display Polycarbonate (PC)
Lens Modified
polyarylate		 Methacrylate resin Modified polyarylate
Main IO-Link functions Operation mode switching between Light ON and Dark ON, setup of the instability
detection level for light receiving and non-light receiving, timer function of the
control output and timer time selecting, instability output (IO-Link mode) ON delay
timer time selecting, setup of a teaching level and execution of teaching, setup of
light receiving sensitivity level, monitor output, operating hours read-out, and initial
reset
Commu-
nication
specifi-
cations		 IO-Link specification Ver 1.1
Baud rate -IL3: COM3 (230.4 kbps), -IL2: COM2 (38.4 kbps)
Data length PD size: 2 bytes, OD size: 1 byte (M-sequence type: TYPE_2_2)
Minimum cycle time -IL3 (COM3): 1 ms, -IL2 (COM2): 2.3 ms
Accessories Instruction manual (Neither Reflectors nor Mounting Brackets are provided with
any of the above models.)

Note: 1. Altitude: Up to 2000 m, Pollution degree: 3, Enclosure type: Type1.
*1. Values in parentheses indicate the minimum required distance between the Sensor and Reflector.

last update: October 1, 2024

Product Category

Products

About Us

Solutions

Privacy

Services

Resources

Omron Automation is an industrial automation partner that creates, sells and services fully integrated automation solutions that include sensing, control, safety, vision, motion, robotics and more.

Follow Us

Youtube Facebook Linkedin
© Copyright OMRON Corporation 2000-2020. All Rights Reserved.